tipc-link

An ACTIVE link is serving traffic. Two links to the same node can become ACTIVE if they have the same link priority. If there is more than two links with the same priority the additional links will be put in STANDBY state.

A STANDBY link has lower link priority than an ACTIVE link. A STANDBY link has control traffic flowing and is ready to take over should the ACTIVE link(s) go down.

The Maximum Transmission Unit. The two endpoints advertise their default or configured MTU at initial link setup and will agree to use the lower of the two values should they differ.

The total amount of transmitted or received TIPC packets on a link. Including fragmented and bundled packets.

Represented in the form fragments/fragmented. Where fragmented is the amount of data messages which have been broken into fragments. Subsequently the fragments are the total amount of packets that the fragmented messages has been broken into.

Represented in the form bundles/bundled. If a link becomes congested the link will attempt to bundle data from small bundled packets into bundles of full MTU size packets before they are transmitted.

Shows the average packet size in octets/bytes for a sample of packets. It also shows the packet size distribution of the sampled packets in the intervals

0-64 bytes
64-256 bytes
256-1024 bytes
1024-4096 bytes
4096-16384 bytes
16384-32768 bytes
32768-66000 bytes

states - Number of link state messages

probes - Link state messages with probe flag set. Typically sent when a link is idle

nacks - Number of negative acknowledgement (NACK) packets sent and received by the link

defs - Number of packets received out of order

dups - Number of duplicate packets received

The number of times an application has tried to send data when the TIPC link was congested

Max is the maximum amount of messages that has resided in the out queue during the statistics collection period of a link.

Avg is the average outqueue size during the lifetime of a link.

The priority between logical TIPC links to a particular node. Link priority can range from 0 (lowest) to 31 (highest).

Link tolerance specifies the maximum time in milliseconds that TIPC will allow a communication problem to exist before taking the link down. The default value is 1500 milliseconds.

The link window controls how many unacknowledged messages a link endpoint can have in its transmit queue before TIPC's congestion control mechanism is activated.

The threshold specifies the cluster size exceeding which the link monitoring algorithm will switch from "full-mesh" to "overlapping-ring". If set of 0 the overlapping-ring monitoring is always on and if set to a value larger than anticipated cluster size the overlapping-ring is disabled. The default value is 32.

Represents the event count in a node's local monitoring list. It steps every time something changes in the local monitor list, including changes in the local domain.

Represents the current count of cluster members.

The current supervision algorithm used for neighbour monitoring for the bearer. Possible values are full-mesh or overlapping-ring.

The node status derived by the local node. Possible status are up or down.

Represent the type of monitoring chosen by the local node. Possible values are direct or indirect.

Represents the domain generation which is the event count in a node's local domain. Every time something changes (peer add/remove/up/down) the domain generation is stepped and a new version of node record is sent to inform the neighbors about this change. The domain generation helps the receiver of a domain record to know if it should ignore or process the record.

The node status reported by the peer node for the succeeding peers in the node list. The Node list is a circular list of ascending addresses starting with the local node. Possible status are: U or D. The status U implies up and D down.

Represents the nodes and their status as reported by the peer node. These nodes were not applied to the monitoring list for this peer node. They are usually transient and occur during the cluster startup phase or network reconfiguration. Possible status are: U or D. The status U implies up and D down.

Forces all multicast traffic to be transmitted via broadcast only, irrespective of cluster size and number of destinations.

Forces all multicast traffic to be transmitted via replicast only, irrespective of cluster size and number of destinations.

Auto switching to broadcast or replicast depending on cluster size and destination node number.

Set the AUTOSELECT criteria, percentage of destination nodes vs cluster size.